how to

Here are my pics and write up for a 3rd gen RAM Mount for the dash so that I could use a tablet for maps and vehicle information while underway. This process involves removing the dash which will take a few hours. If that is something you want to undertake I would consider proactively replacing...

Does your steering wheel cruise control buttons in your 95-01 Ford Explorer look like a broken sad mess? Sticky, nasty, or completely MIA?? No problem! Get those old and busted buttons out and the new hotness buttons in place quickly and easily! The replacement of these steering wheel cruise...

Hello i posted a video showing how to replace the brake booster on the 95-01 explorer

I’ve got a 2016 limited with the 3.5, around 68,000 miles. Without any codes or warnings, It wouldn’t start this morning, and after getting it fired up from a booster got it to a shop. They said the alternator was bad and want $900+ to fix. Not happening. I’ve searched the forum for more...

So recently I just installed a cb into my 02 Ex. I wasn’t able to find very many threads on here about installing one but I believe I have a good write up. The hood channel mount, coax cable, and antenna were ordered on Amazon with Prime. They all are Firestik brand. I will post more pics of...

Rear links Torque 58 foot pounds Get under truck Locate link Remove nut and bolt mine was a 16mm Remove link Wiggle new link in and install new nut and old bolt torque them to spec MORE pics Now the front don't know about torque spec I tighten them in till the rubber...

I wasn't ready to spend 250+ on roof crossbars so I came up with three 3,5mm thick plates with 6 holes and spray painted it black and put some plastic chrome imitation on the borders so it blends with the OEM bars. all the details are in the pictures I've attached but if you have any questions...

I purchased my 2004 XLT 4.0L V6 4x4 as my "mountain car". I wish I had a V8 however it gets the job done as-is. I have been having some issues with the auto 4x4 engaging when I did not want it to so I will be doing the brown wire mod once the temp gets back to the double digits. Anyways my...

Can someone please tell me if the cam sync is supposed to sit flush? I can feel the gears twist as they mesh but the "shiny" exposed portion (red circle) has me second guessing myself. Please ignore the orientation of of the install tools arrow, I can explain if necessary.

As a new member I would like to contribute by doing a quick how to write up. I was unable to find one on this issue anywhere. Most forums and professionals will tell you to just replace the whole unit once it starts making noises or even smoking. This solution will not help you if your problem...

Hey guys, This is my latest video on How To Flush and Bleed Your Brakes. Brake fluid absorbs water so after about 3 years you should flush them. While I know of no one who flushes their fluid that often I figured after 14 years I should flush them out lol. Let me know what you think...

Hey Guys, So here is my latest video: How to Change Transfer Case Fluid. I really like this one because it is easy, clear and straighforward. I figured this would help some of you as well who need to change your fluid. What do you think? Ps. Thumbs up the video on youtube if you can...

I'll never have to run outside to roll my windows up during a rain storm again!...I just installed a ebay window rollup module on my 98 X. This will roll up 2 or 4 windows...

Alright, I just pulled another all nighter doing homework and am ending it at 5:45 am with this thread! In between relentless homework assignments and exam prep, I have been cruising around looking for components to my audio system. I thought that I should start a build thread for it because I...

Looking at the boards, it sounds like a lot of people are interested in a flat black paint job. I've been thinking about doing a flat black paint job, especially since I had to replace a lot of the front end post-Bambi. This is a happy California truck, no rusty spots on the body or anything...

The following write up is for informational purposes only. This is just an account of what I did while troubleshooting an overheating anomaly (see thread here) on my 2000 Explorer Limited. As part of my T/S I removed the thermostat and took some notes and pictures along the way. I was not sure...

this will show you step by step how to install power seats into an XLS. Tools needed: 15mm deep socket electrical tape heat shrink butt connectors wire stripper/cutter and about 2 hours time, patience is key. DRIVERS SEAT! step one. find a good donor vehicle, if you and see the seat...

I am looking for how to instructions for changing the transmission fluid in my 2002 Ford Explorer Sport Trac 4X4

Hey everyone, I'm new to the site, I have a '96, 4.0 automatic, black explorer, competely stock to my knowledge, thought I would love to black it out soon, or over this summer, any ideas on how to do this would be great as I would like to do it myself but have never tried somehing like this...

Hey there, I have a 99 xls with the factory audio system. I went to the local pull-a-part this weekend and found a 99 xlt with the jbl premium system in the back. I pulled it out and was able to get the complete wiring (including the plug) that connects under the glove box on the passenger...

I started on replacing my filthy seat belts, and wanted to give a "how-to". Difficulty scale from 1-10: 2. This is a VERY easy and simple project that makes a huge difference to you and your passenger as you put the seat belts on for each drive you take. Here are two of the belts side by...

Hello once again. I am going to be replacing my seat belts, and I need some advice. How do you replace the belts and mechanisms? Is there a way to snake them out of the hole(s) of the plastic trim, or is the trim supposed to be replaced with the belt and mechanism as a whole? I have...

I have been browsing this forum for a couple of days, I have an 03 4wd with the 4.0 and i have seen it hinted that you can set this engine back into time without having the special tools. Can somone let me know how this is done ? I am having to replace the front cassete in addition to the...

1998 Ford Ranger 4.0 XLT 4X4 186,000 miles. I have a big leak going on and it appeared to be coming from in between the (Driver's side) head and the lower intake. Being my first time really tearing into an engine this deep, do any of you have any suggestions or tips for me? If anyone has...

Alright here it is! I've been thinking about many projects on my X for a while. Now that i'm back from afghanistan, I got all the time and money I need to make them and I decided to make something useful out of it and make a how-to of everything i've done ou will be doing on it. First, I...

Thanks to MustangP51's LED threads I've gathered enough courage to attempt to make my own LED Underbody kit after I blew a neon tube. LED's are much brighter, require less power, and are virtually indestructable. I've only fabricated the two sides, but I have them installed and wired, and as...