Section525 - D44 2nd gen. leaves SAS

[410Fortune]

I dont care what they say my ex has the red switch I am going to replace that sucker recall or not!

 

[section525]

No locker? only L/S :thumbdwn: Get your self a locker there buddy.

Damn you Stic-o! I bought a used lunchbox locker from my 4wd shop guy today. So.. looks like it's going in tomorrow/Saturday too (if I can get my hands on an open carrier). Locked front and rear and 4wd by Sunday!

 

[Stic-o]

Damn you Stic-o! I bought a used lunchbox locker from my 4wd shop guy today. So.. looks like it's going in tomorrow/Saturday too (if I can get my hands on an open carrier). Locked front and rear and 4wd by Sunday!

I got one you can have...A bit used though! :

 

[section525]

You know my address. :

 

[badge49]

You guys need help this afternoon? Ran into Phil last night...said something about you guys doin' the gears today. I'll give him/you a call later, gotta check up on your ex, it's looking pretty sweet!

 

[FROADER]

Surprised you don't have an 8.8 laying around the house... :

 

[section525]

Well it was a long day of not getting much accomplished. Hit a couple places up for an open carrier. Finally ended up pulling one from the junk yard. Went good. Except for when we went to install the locker. It was the wrong size carrier (different cross pin width). Damn it. So, looks like we need to go hunting again.

Then we tore out the front axle. Starting working on the gears and locker for that. It's a lot of trial and error trying to get everything right when you don't have the old shims to sorta go off of. So we played with it till 12:30AM trying to get a pattern we like with the acceptable backlash. Decided to call it a night and try some more in the morning.

But, things might still work out by the end of the weekend. I got some metal to make the new crossmember and the front driveshaft. So as long as we get these gears set to our liking in the morning.. I have all Sat and Sun to finish it up.

Oh yeah, and the Ford dealer is keeping my Mountaineer until Monday because apparently it caught on fire. :

 

[zainyD]

What x-member, tranny x-member?

 

[section525]

What x-member, tranny x-member?

Yeah, the tranny crossmember.

But, I'm building a sorta.. middle.. crossmember that will link the shackle hangers on the front springs and also be where the belly skid will bolt to. So the skid will bolt to the rear tranny xmember too. It should be pimp.

Shackle hanger xmember:

 

[section525]

Back to fabbin'. This is definitely the part I dig most.


Here's the new tranny x-member so far:

 

[zainyD]

Very nice!!!

 

[section525]

Front gears and locker are now in. The axles have new u-joints. Pretty much everything is ready to go back together now. We left it all apart so it'll be easier to move the axle under the truck. Which, we didn't do because I really want to build the new shackle hangers/x-member before throwing it back in. So tomorrow will be another fab day.

 

[FROADER]

Hell yeah! How was putting the new springs in the EZ?

 

[section525]

Yeah. Phil put them in in a few seconds.

 

[FROADER]

Went in easy then. Hopefully my intraweb will be working in the am tomorrow.

 

[DB_1]

Kewl

You gonna head down for a T-haven run or 2 when it's done?

 

[section525]

Kewl

You gonna head down for a T-haven run or 2 when it's done?

Don't think I'll be able to make it before the Feb run. I'll have skoo from Nov-March so no ca$h flow.



Tore out the old shackle hangers and here is the new ones so far.

 

[Stic-o]

Your makin' this kinda hard on yourself.... What happen to "look at me do a SAS in a weekend" blah blah blah. Yet I here of no 4wd, and see no off roading pictures? :

 

[section525]

I'm just fixing stuff before I have to fix it out in the woods in 5' of snow at 2AM. :

You just wish you had the bling factor this is going to have.

 

[Stic-o]

I'm just fixing stuff before I have to fix it out in the woods in 5' of snow at 2AM. :

You just wish you had the bling factor this is going to have.

Rocks don't care about Bling!